Jeep cj7 clutch linkage




Jeep cj7 clutch linkage

Article Navigation:
  • Photo
  • Jeep CJ-7 Clutch Linkage Upgrade
  • Video
  • RELATED PAGES
  • Take your clutch game to the next level and make your Jeep's manual transmission shifting smooth as fresh-paved asphalt with Jeep CJ clutch parts for sale and.

    Jeep FC () w/ engine; Clutch Pedal Only. Jeep CJ ( ) w/ L, L or L engine; w/ /8″ long rod; Clutch bellcrank to fork.

    Buy Jeep clutch parts for your CJ5, CJ7, CJ8 online at Morris 4x4 Center. Get low prices and free shipping on pressure plates, clutch linkage, bearings and.

    Jeep cj7 clutch linkage

    Jeep cj7 clutch linkage

    Not only are the clutch rods studier than the factory parts, but the pedal rod is bent to better conform to its path through the firewall and down to the bellcrank, and adjustable heim ends replace the bare metal factory rod end-flange connections to provide a more durable clutch rod assembly that can help deliver smoother and more precise clutch engagement. The hiem bolts were then tightened to the flanges, and after a final check for proper rod lengths, the backing nuts behind the heims and the adjustable ball end were tightened. All that was retained for installation of the Barnett Performance Products replacement are the adjustable ball-end, and if they are not torn, the rubber boots of the ends of the bellcrank. The new Barnett Performance Products bellcrank was completely assembled, mounted to its brackets with the supplied C-clips, and then the two bellcrank brackets re-installed. Unlike the factory rod, the Barnett Performance Products rod has adjustable ends.

    Jeep cj7 clutch linkage

    Jeep cj7 clutch linkage

    Jeep cj7 clutch linkage

    Jeep cj7 clutch linkage

    Jeep cj7 clutch linkage

    There are a number of reasons you could be experiencing sloppy clutch action in your Jeep CJ-5 or CJ However, before you finish diagnosing your clutch trouble, consider that the trouble or part of trouble may be a worn out linkage. Each kit includes all the parts to replace the worn-out or bent bellcrank and clutch rods for that vehicle, and all the hardware and bushings to complete the job. Not only are the clutch rods studier than the factory parts, but the pedal rod is bent to better conform to its path through the firewall and down to the bellcrank, and adjustable heim ends replace the bare metal factory rod end-flange connections to provide a more durable clutch rod assembly that can help deliver smoother and more precise clutch engagement.

    This entire job took about one hour to complete and made a big difference. See how we did it. Subscribe to a magazine. Transmission Drivetrain on March 31, Share this. Bourdon Technical Editor, Jp Magazine. Replacement bushings for the bellcrank, and all the hardware for the installation are also included.

    Jeep cj7 clutch linkage

    The bracket for the inside end of the bellcrank to the transmission bellhousing was unbolted, leaving the short clutch rod connected to the bellcrank.

    This is what you are replacing. Over time and thousands of clutch applications, the rod ends can wear down, the holes in the bellcrank flanges can wear into over-round or oval shapes. As well, the bellcrank flanges and mounting brackets can become bent because the bellcrank is mounted on the frame at one end and the bellhousing at the other end, and these two points are often not aligned during off-road driving due to the movement of the frame or powertrain in relation to each other.

    Jeep cj7 clutch linkage

    All that was retained for installation of the Barnett Performance Products replacement are the adjustable ball-end, and if they are not torn, the rubber boots of the ends of the bellcrank. This helps to more squarely place force on the connection at that end of the bellcrank.

    Unlike the factory rod, the Barnett Performance Products rod has adjustable ends. A key ingredient in the Barnett Performance Products clutch linkage replacement kit is the three small heim joints that while allowing for a smoother and more precise movement and thus smoother and more precise clutch engagement of the entire linkage from pedal to clutch, also reduce wear and tear on the rod end connections to the pedal and bellcrank.

    Here you see one part of the problem with sloppy clutch engagement in this CJ The old rod had worn an oversized hole in the top end of the clutch pedal, creating free-play between the pedal and rod. This saved the cost of buying a new clutch pedal. The new Barnett Performance Products bellcrank was completely assembled, mounted to its brackets with the supplied C-clips, and then the two bellcrank brackets re-installed. To ensure proper fitment, the new clutch rod and lever rod were then adjusted for approximately proper lengths but locking nuts left loose.

    Jeep cj7 clutch linkage

    The hiem bolts were then tightened to the flanges, and after a final check for proper rod lengths, the backing nuts behind the heims and the adjustable ball end were tightened. Sources Barnett Performance Products. Subscribe to the Magazine. Get Digital Get Print.

    Clutch linkage update and response to hate mail



    • Подписаться по RSSRSS
    • Поделиться VkontakteVkontakte
    • Поделиться на FacebookFacebook
    • Твитнуть!Twitter

    Leave a Reply

    Return to Top ▲TOP ▲